Uncategorized
Antislip Ladder Rung Covers
It is important to significantly enhance safety on most ladders by adding nonslip ladder rung covers which will increase the amount of available surface area where there is any foot contact. The mostly smooth, small foot surface area on ladder rungs present an extremely high-risk hazard that needs to be made safe by being covered in an antislip coating as specified in AS 1657.
Advance Anti-Sip Surfaces antislip Class 1 metal backed Ladder Rung Covers are available in two distinct styles, circular and square, which snap fit easily over the rung providing a long lasting, highly visible surface to climb. Ladders can be a means of access that is used less often than walkways or stairs, therefore adding Advance Anti-Sip Surfaces antislip Ladder Rung Covers will not only make the ladder a safe piece of equipment, they will usually last for the useful life of the ladder.
Advance Anti-Sip Surfaces antislip Ladder Rung Covers will eliminate the problem of slippery ladders and protect employees and visitors in the area from slips and falls.
Product Features
Here are some great features of Advance Anti-Sip Surfaces antislip Ladder Rung Covers:
- Made in circular, square or custom designed profile
- Highly visible in our bright Safety Yellow
- Many colours available
- Snap fits over ladder rungs tightly
- Resilient to impacts
- Circular rung covers backed with quality Colorbond® coated steel
- Can be retrofitted on site or as specified as an OEM safety enhancement
- Easily installed using adhesive or mechanical fastening
Product Benefits
When Advance Anti-Sip Surfaces antislip ladder rung covers are installed, some of the benefits are:
- Increased safety on ladders
- Reduction in the number of slips and falls from ladders
- Increases the useful life of the ladder
- A wide variety of sizes
- Comes in different colours
- Comes with a very high anti-slip rating
- Does not peel, crack, become brittle or wear out
- Resistant to chemical corrosion
- Complies with required safety standards
- Quick and simple to install
- Extremely durable with a high traction design
Antislip Tapes

Antislip tapes
Advance Anti-Slip self-adhesive antislip tapes provide a robust slip resistant surface to help prevent slips, trips, stumbles, tumbles and falls.
The durable non slip low-profile design enables light to medium pedestrian traffic to navigate stairways, steps, stairwells, landings, platforms, ramps, walkways and ladders freely, which helps in reducing slip hazards, incidents and injury.
Our non-slip tape range has applications on flat surfaces, entranceways, ramps, steps, ladders, forklifts, skateboards, construction machinery, plant equipment, marine vessels, transport vehicles and trailers, public transport vehicles, and many more surfaces where secure footing is required.
Product Features
- Durable grit surface to provide safe footing,
- Adheres to smooth, clean, dry surfaces,
- Available in sizes 25mm to 450mm,
- Comes in different colours,
- Australian Standard AS/NZS 4586:2004 compliant,
- Temperature resistant from -5°c to 50°c,
- Provides an instant non-slip surface.
Product Benefits
- Quick and easy to install,
- Improve safety and performance in work areas,
- A versatile economic solution,
- Helps prevent slips, trips, falls and accidents,
- Use on steps, ladders, ramps, walkways, platforms, gangways, gantries, construction equipment, trailers, forklifts, boats, trains, buses, work vehicles and more,
- Suitable for indoor and outdoor applications.
Antislip Stair Nosings
Slips, trips and falls on stairways are a more common occurrence in industrial and commercial environments than they should be, sharing about the same frequency of incidents being reported.
Advance Anti-Slip Surfaces offers a comprehensive range of antislip stair nosings that suits all types of steps or stairways. Stair Nosings that protect more than the steps leading edge from wear, but ensures that the stairway is visible to workers and visitors, and prevents incidents from occurring.
Nonslip stair nosing can be known by many names such as stair capping, bull nosing, stair treads, step covers etc. No matter what they are known as, Advance Anti-Slip Surfaces antislip Stair Nosings provide the most durable, highest quality, best valued protection for your assets by preventing loss due to a slip, trip or fall.
Advance Anti-Slip Surfaces antislip Stair Nosings have a very long serviceable life which is backed by our extensive warranty. They can be fixed permanently in moments without the risk of coming loose due to heavy pedestrian use. The highly visible Safety Yellow finish ensures the stairs leading edge will be seen while ascending or descending the stairway.
Unlike other types of products that may crack, become brittle, need time to cure, peel or delaminate, Advance Anti-Slip Surfaces antislip Stair Nosings are manufactured on a metal backing ready to install and use quickly so there is no inconvenience to pedestrians that need to walk in that particular area.
Product Features
Here are some great features of Advance Anti-Sip Surfaces antislip Stair Nosings:
- Bright Safety Yellow nonslip coating provides high visibility and sure footing
- Manufactured to customer requirements utilising the most durable components available
- Made with strong metal backing
- High impact resistance
- Other colours available
- Easy to install
- Custom make sizes available
- Chemical resistant
- Suitable for all stairway applications
- Covered by an extensive warranty period
- Protects the stairs leading edge from wear over time
- Extremely high antislip rating that has been tested and certified
Product Benefits
When Advance Anti-Sip Surfaces antislip Stair Nosings are installed, some of the benefits are:
- Superior slip and fall prevention in stairways, landings and pedestrian access areas
- Easy to clean
- No down time, simply install and it is ready to walk on
- Can easily be replaced if damaged
- Reduces MTI’s and LTI’s
- Fewer incidents of injury, saving any litigation costs
- Protects the stairs from wear over time saving maintenance budgeting
- Very easy to set up which saves on installation costs
Fireseal Pipelock PL
A complete factory made seal for single plastic pipes.
- Optimized system for single plastic tubes.
- Very easy and quick installation.
- Maintenance free.
- Corrosion free.
- Avilable sizes: PL 55, PL 82, PL 110 and PL 160.
- Classification: A0 – A60
Fireseal FLEX-D system
Our most commonly used system which can be used for several different applications such as cables, pipes and ductwork sealings.
-
Sealing system for cables, pipes, ductwork and the alike.
-
20 min installation – no special tools required.
-
Suitable for penetrations with limited free surface area.
-
Smoke, gas, water and pressure resistance.
-
Movements and vibration of penetrating pipe(s) and cables are accepted.
-
Well packed cable bundles are acceptable.
-
Changes, repairs or retrofits are made easy.
-
Classification: A0 – A60 & H0 – H60.
Fireseal Kniparen 50
A complete factory made seal for singe metal/plastic pipes or multiple cables.
Very easy and quick installation.
Sizes: 50 mm
Classification: A0 – A60
ZincTape Anti-Corrosion System
ZincTape Anti-Corrosion System
ZincTape® consists of a high pureness zinc-tape (> 99,95% of the chemical mass of zinc) with a nominal
thickness of 0,08 mm. This tape is supplied with a > 0.025 mm thick adhesive, which can resist continuous operating temperature of 80° C and which reacts under electro-conductive pressure. The adhesive layer is covered by a siliconised paper, which protects the band from getting damaged or polluted until the tape is applied.
ZincTape® is designed to cover the surface of iron, steel, aluminium and light metals in order to protect them from corrosion. This is achieved by pressing it on the surface that needs to be protected from corrosion. This method is commonly known as “Laminar Zinc Coating”.
The adhesive coat, which is applied only on one side of the zinc tape, consists of a matrix of adhesive and a percentage of zinc powder. Through the addition of zinc powder we have achieved the most important effect, which is making the adhesive itself electro conductive. This process allows the adhesive to create an electrical couple between the surface that needs to be protected and the zinc tape, so that the zinc can act as galvanic anode.
As a consequence of the unique manufacturing process and the high pureness of the employed zinc, the band has an absolutely homogeneous and isotropic microstructure, which cannot be found in other protection systems.
For this reason, any pitting or any form of local corrosive attacks are avoided. Therefore we can state that, owing to the following features:
• stopping any direct corrosion;
• active anticorrosive protection thanks to the electrical contact between the surface to be protected and the zinc layer, which, in the presence of an electrolyte, reacts as a sacrificial anode;
• presence of an adhesive layer, anchored on the surface to be protected, which is an additional defense against corrosion.
The coating with our zinc layer assures a cathodic protection of metallic surfaces for a time, that, in most cases, is equal or longer than the lifetime of the structure to be protected.
Application fields
- Lamp Post – Lamp post are protected by ZincTape, on the base that is the critical part of the surface. The coating is usually carried out by qualified applicators or by the supplier of metallic poles.
- Automotive – Protection of window borders, chassis, roofs and other areas where water can seep through. For hinges and car doors or other particular hot spots ZincTape can offer special shapes based on the client’s needs and made on purpose to avoid corrosion problems.
- Oil & Gas – Pipes and out-of-ground pipes. Sea platforms, harbour structures, wharves, piers and off-shore platforms Above-ground apparatus and components of refineries.
ZincTape is environmental friendly and it is available in different sizes and thicknesses.
Fitok Medium & High Pressure Valves & Fittings
General Instrumentation Fittings
General Instrumentation Valves
Medium & High Pressure Fittings
Medium & High Pressure Valves
Fittings for Semiconductor and Gas applications
Valves for Semiconductor and Gas applications
L Series Liquid Sampler
G Series Gas Sampler
Firestop Sealant 3000, 310ml/cartridge
Fire-retardant silicone elastomer
Firestop Sealant 3000 is used in the complexes FS-Flex D and FS-Universal and is designed mainly for sealing of cable, pipe and vent passages and entries in the refractory structure categories of fire safety EI 60 – EI 150, such as concrete slabs and hollow drywall.
Description
FireStop Sealant 3000 is a silicone specially developed for fire rated penetration sealing.
Packing: 15 cartridge/carton – 310ml/cartridge
Color | White, gray, black |
Density | 1.5 kg / dm 3 |
Working period | 10 – 30 min. |
Curing time, 3 mm | 24 h. |
Full cure | 14 days |
Low setting (min) | + 5C |
Operating temperature (max) | 250C |
Flexibility | + (-) 50% |
UV resistance | Very high |
Tensile | 0.7 MPa |
Shelf life | 1 year (in a sealed pack. While so-re below 32 C) |
Part Number |
Color |
Size ml |
Units.measured. |
Pieces in pack. |
Number of cartridges in 1 carton |
100721 |
White |
310 |
ml |
1 |
15 |
100722 |
gray |
310 |
ml |
1 |
15 |
100723 |
Black |
310 |
ml |
1 |
15 |
BW Gas Monitors and Docking Stations
BW GasAlert Quattro
- Rugged 4-Gas Confined Space Unit
- IP67 Rated – water and dustproof
- Large easy to read LCD
BW GasAlert Max XTII
- Detects O2, LEL, CO, and H2S
- Electronic sampling pump built in
- Includes sampling line and sintered filer
BW GasAlert Clip
- Compact and cost effective single gas monitor
- Available in 24 and 36 months disposable
- Suitable for O2, CO, SO2 or H2S
BW Technologies BWC2-H BW Clip Single Gas H2S Monitor
BW MicroDock II Test Station
- Ensure safe use of monitors with regular bump testing
- Save money by conducting your own calibrations on site
- Fully automated process – just press the button!